Steering and Suspension

Adjustable Prop shaft SeparatorWill fit most makes and models of vehicles - except Seat.

Audi / VW Ball Joint Toolfor holding the lower ball jointwhen removing and installing onAudi A4 | A5 | A6 | A7 | Q5

4pc VAG Subframe Locating Pin SetFor precisely aligning and mounting the subframewhen replacing the vibration isolators / rubber bushings.Also jobs...

Small Universal Press Support RingOuter diameter : 115mmInner diameter : 100mmHeight : 160mmWall : 7.5mmCapacity : 10Tfor the removal of Wheel Bear...

Angled clamps mounted at 90 degrees, for lateral clamping and parallel pressing of the earcup, suitable for tight spaces.For the assembly of Stainl...

5pc Ball Joint and Tie Rod Separator SetTie Rod/ Pitman Arm Tool KitTie Rod Spreader with 11/16in. Wedge OpeningBall Joint Separator with 15/16in. ...

●Applications: Front wheel drive Mercedes-Benz Sprinter, including eSprinter, (2018 on).●Allows access to the top strut fixing for removal of the s...

Large Universal Press Support RingOuter diameter : 180mmInner diameter : 160mmHeight : 160mmWall : 10mmCapacity : 40Tfor the removal of Wheel Beari...

21pc Master Adaptor Set Ball Joint Service KitWith 4 Wheel Drive AdaptorsBrake Anchor Pin Removal and InstallationThis tool kit is designed for use...

2pc Coil Spring CompressorFor use with 21mm socket or spannerTotal Length : 280mmFor the quick and safe removal or installation of coil springs.Sui...

Suspension Strut toolDual Size : 5 / 6mm x 182mm long.Prevents the damper piston rod from rotatingwhile removing and replacing the rear strut.Suita...

The Steering Wheel Puller for GM is a specialized tool designed for removing steering wheels from various General Motors (GM) vehicles, including V...

The Bushing Tool for Tesla Model 3 Electric Motor is a specialized tool designed for servicing the front electric motor of the Tesla Model 3. It is...

Steering Wheel Remover / Lock Plate CompressorFor vehicles with or without Tilting SteeringCompresses steering wheel lock plate to remove and insta...

43pc Turnbuckle for Shock Absorber TopFor counter holding the piston rod while loosening.Go-Thru Ratchet : 19 | 22mm.Deep Sockets : 14 | 16 | 17 | ...

Differential Front Bush Tool Set For BMW  ●Suitable for the removal/installation of the front differential bush on BMW●Applicable: BMW 5,6,7 series...

Automatic Transmission Clutch Spring CompressorFor servicing the transmission rear clutch Piston snap ring.Adjustable for most cars and light truck...

Air Powered Hydraulic Coil Spring Compressor Station1000kg Air Actuated Hydraulic Unit with Alternative Foot OperationQuicker and Easier than using...

Manual and Hydraulic Coil Spring Compressor Work Station1000kg Foot Operated Hydraulic UnitQuicker and Easier than using ratchet driven spring comp...

2pc Coil Spring Compressor for MacPherson StrutsCompresses the coil spring to replace the shock absorber unit or spring.Widely used on the front su...

Guard Cover for Hydraulic Spring CompressorFit on CT1945 ,CT1946 ,CT1321 ●Steel construction.●Powder coated.●Safety guard cover prevents injury

Steering Wheel Lock Plate RemoverIdeal for detaching steering column lock plates on the majority of cars with air bags1-9/16in. x 18mm and 14 x 1.5...

Universal Bearing Packer111mm Cone Diameter.Suitable for packing bearings with an even spread of Grease.A Clean and Quick method - place bearing on...

17pc Bearing and Bushing Driver SetFor Bearings / Vibration Isolators / Silent Blocks3 Driver Handles : 113mm | 140mm | 162mm14 adaptors : ID 10 - ...

Rear Suspension Bushing Isolator Removal Toolfor Vauxhall / OpelFor Upper and Lower Suspension Bushings

For quick and easy disassembly of universal joints on cardan shafts.Puller foot opening: 65 mmPuller foot height: 8 mmPuller foot depth: 65 mmTotal...

Replacement Pedalfor Coil Spring Compressor Station CT1946

CV Boot ToolFor installing vehicle rubber CV boots without dismantling the CV joint.Steel Centre / Plastic Composite Cone.Diameter Size : 100mm Ex ...

Mercedes M-Class Ball Joint Pin Socket3/4in.Dr / 4 PinFor ML-class W163 < 2005 and W164 2005 <For servicing the front and rear axle suspen...

Universal Ball Joint PullerFor all types of vehicles20mm Jaw opening adjustable up to 50mm

●Used to keep alignment of the sub frame during reassembly.●Size: 4pc M12 x 1.5mm x H5, 2pc M10 x 1.5mm x H5●OEM: T10486A, T10227●Compatible with :...

Medium Universal Press Support RingOuter diameter : 140mmInner diameter : 120mmHeight : 160mmWall : 10mmCapacity : 40Tfor the removal of Wheel Bear...

Trailing Arm Bush Tool Set ●It's designed for disassembly and assembly of the silent bearings in the trailing arm of the rear axle, no disassembly ...

For the removal / installation of the front Bushing Isolators on VW vehiclesCan be used in-situ without removing assembly from vehicleMounting adap...

Bushing Service Tool - VAGFor replacing the front suspension bushingson VW Polo 2002 and later.